Highly wear resistant
Resistant to most aggressive environments, including chemicals
Higher water resistance, boiling waterproof
Hard surface, durable and stable
Fresh indoor air quality, free from toxic VOCs
Resistance to temperature variation: through a range of -40°C to +50°C (-40°F to +122°F), comes in a variety of thicknesses and sizes
Products that improve your cost, material and energy efficiency
Reliable and timely deliveries
Local knowledge, support and service
Solutions for every application
Proven and documented technical data and environmental statements
Unit |
CCX/CDX |
||||
Composition | All - Eucalyptus | Pine/Eucalyptus | |||
Thickness | 15mm | 18mm | 15mm | 18mm | |
References | TECO 09-P-0026 | TECO 08-P-0127Weyco WSE09-004 | TECO 09-C-0027 | TECO 06-P-0180Weyco 09-004 | |
Span Rating | in/in | 40/20(3) | 48/24(3) | 40/20(3) | 48/24(3) |
Group Rating | Group 1(3) | ||||
Average Weight | Kg | 23.3(3) | 27.7(3) | 24.6(3) | 29.2(3) |
Density (6%MC) | Kg/m3 | 503(3) | 503(3) | 537(3) | 533(3) |
MOEP - Parallel | N/mm2 | 8,110(3) | 8,730(3) | 8,130(3) | 8,260(3) |
MOEP - Perpendicular | N/mm2 | 2,590(3) | 2,460(3) | 2,700(3) | 3,160(3) |
MORP - Parallel | N/mm2 | 31.3(3) | 32.0(3) | 29.2(3) | 31.2(3) |
MORP- Perpendicular | N/mm2 | 16.8(3) | 15.1(3) | 25.6(3) | 22.6(3) |
Maximum Shrinkage - Parallel | Percent | 0.21 | 0.33 | ||
Maximum Shrinkage - Perpendicular | Percent | 0.28 | 0.30 | ||
Screw Withdrawal(1) - Face | N | 1330 | 1670 | ||
Screw Withdrawal(1) - End | N | 1100 | 1290 | ||
Screw Withdrawal(1) - Edge | N | 1005 | 1250 | ||
Staple Withdrawal(2) - Face | N | 961 | 1090 | ||
Staple Withdrawal(2) - End | N | 992 | 1240 | ||
Staple Withdrawal(2) - Edge | N | 1290 | 1150 |
Waterproof,
Strong and light
Meets EUTR standards,
Meets European E1 formaldehyde emission requirements (EN 120:1992) and also California ARB regulation P2
100% natural whole piece or spliced Eucalyptus or Pine Veneers of 3mm and/or 3.6mm thickness throughout the plywood having open knots and occasional open splits or joints in the core.
Phenolic resin cross-bonded weather resistant gluing according to EN 314-2 class 3 exterior.
Wood veneer is a living material and is subject to moisture movement according to surrounding conditions, which affects the flatness of panels. It is important to condition the panels to reach a moisture content near to the equilibrium of their permanent environment.
Like other wood-based panel products, Birch Plywood is also hygroscopic and its dimensions change in response to a change in humidity. A change of 1% in moisture content typically increases or decreases the length, width and thickness by 1% in dimensions and thickness. It is therefore desired that the edges are sealed with a suitable acrylic paint to prevent and/or control ingress of moisture and humidity and consequent swell in thickness and expansion in dimensions.
The recommended stocking conditions are 20°C and a RH of air of about 60%
Eucaply Applications
Eucaply CDX/CCX Plywood is made in a range of thickness from 12mm to 21mm
The most commonly available dimension is 2440mm x 1220mm.